Klõps ikoonil viib faili leheküljele Wikimedia Commonsis.

Fail:Skin depth by Zureks.png

Allikas: Vikipeedia
Jump to navigation Jump to search

Algfail(675 × 670 pikslit, faili suurus: 49 KB, MIME tüüp: image/png)

Lühikirjeldus

Kirjeldus
English: Skin depth vs. frequency for various materials. The equation used for skin depth calculation was

where: δ - skin depth, ρ = resistivity of the material, ω = angular frequency = 2π × frequency, μ = absolute magnetic permeability (μr×μ0)

The materials are as follows:

  • Mn-Zn - soft ferrite 3C90 from Ferroxcube, initial permeability = 2300 (initial, 25 deg C, 10 kHz) and resistivity = 5 Ωm based on catalogue data [1], such ferrite is not a good conductor so the curve is shown here as dashed, just for demonstration how much better such materials are at higher frequencies
  • Al - aluminium, relative permeability = 1, resistivity = 2.7e-8 Ωm based on data from MatWeb [2]
  • Cu - copper, relative permeability = 1, resistivity = 1.7e-8 Ωm based on data from MatWeb [3]
  • steel 410 - magnetic stainless steel 410, permeability = 1000 and resistivity = 5.7e-7 Ωm based on data from MatWeb [4], the highest value of quoted permeability (1000) is used for "worst case" scenario
  • Fe-Si - grain oriented electrical steel (around 97% Fe and 3% Si) from AK Steel manufacturer, permeability = 29,000 and resistivity = 5e-7 Ωm based on manufacturer bulletin [5], maximum value of permeability is read out from the radial plot and it is used to demonstrate the "worst case" scenario
  • Fe-Ni - permalloy (trade name of VACUUMSCHMELZE GmbH & Co. KG is Mumetall), alloy mainly of Fe (around 20%) and Ni (around 80%), values of permeability = 250,000 [6] and resistivity = 5.5e-7 Ωm [7] are based on the manufacturer data.

Red vertical line indicates 50 Hz frequency.


Kuupäev
Allikas Üleslaadija oma töö
Autor Zureks

Litsents

Autoriõiguse omanikuna avaldan selle teose järgmise litsentsi all:
Creative Commons CC-Zero See fail on avaldatud Creative Commonsi üldise litsentsi CC0 1.0 all.
Isik, kes sidus teose selle litsentsiga, on andnud teose avalikku omandisse, loobudes üleilmselt seadusega lubatud ulatuses kõigist õigustest, mis tulenevad autoriõigusseadusest, sealhulgas autoriõigusega kaasnevatest õigustest ja naaberõigustest. Tohid teost kopeerida, muuta, levitada ja esitada; seda kõike luba küsimata ja ka ärilisel eesmärgil.

Faili ajalugu

Klõpsa kuupäeva ja kellaaega, et näha sel ajahetkel kasutusel olnud failiversiooni.

Kuupäev/kellaaegPisipiltMõõtmedKasutajaKommentaar
viimane24. veebruar 2011, kell 23:57Pisipilt versioonist seisuga 24. veebruar 2011, kell 23:57675 × 670 (49 KB)Zureks{{Information |Description ={{en|1=Skin depth vs. frequency for various materials. The equation used for skin depth calculation was : <math>\delta=\sqrt{{2\rho }\over{\omega\mu}}</math> where: δ - skin depth, ρ = resistivity of the material, ω =

Seda faili kasutab järgmine lehekülg:

Globaalne failikasutus

Järgmised muud vikid kasutavad seda faili: